aliasing

n.混淆；折叠失真；〔计〕别名使用；〔物〕假频

网络释义：混叠；走样；混淆现象

网络释义

n.1.折叠失真2.〔计〕别名使用3.混淆4.〔物〕假频1.折叠失真2.〔计〕别名使用3.混淆4.〔物〕假频

1.混叠 alias 别名 别名 aliasing 走样 锯齿化 align 对齐 对齐 ...

3.别名 ATAPI AT 附件包接口 aliasing 混淆 autoexec.bat 自动批处理文件 ...

5.混淆现象 ·位数（ Bits） ·混淆现象（ Aliasing） ·取景器（ Viewfinder） ...

6.锯齿 Aliasing distortion 折叠失真 Aliasing 量化噪声，频谱混叠 Align alignment 校正，补偿，微调…

8.锯齿化 alias 别名 别名 aliasing 走样 锯齿化 align 对齐 对齐 ...

1.Compared to Nyquist sampling, the oversampling technique makes the design of the front anti-aliasing filter relatively easier.此外，相比于奈奎斯特采样，过采样使前置抗混叠滤波器的设计变得容易。

2.This method allows a value class to be manipulated as an object while it retains the aliasing behavior of a value class.这个方法可让实值类别当做物件来操作，同时保留实值类别的别名行为。

3.the general condition of the sheep in hand to allow the best dry-cleaning fabrics, clothing aliasing immersion will pan color.的手羊的一般条件允许最好干洗面料，服装混浸泡将泛色。

4.Because of wet cloth to easily damage the hair texture and a sense of style may also be caused by the Pan- aliasing or color.因为湿先容易损伤衣料的纹理和毛感，也可能造成款式走样或泛色。

5.Disaster 1: I cut the image with the Magic Wand and pasted it onto a red backdrop, messing up the anti-aliasing around the woman's face.灾难一：我用魔棒工具将图像切割下来之后粘贴在红色的背景上，这样就把女人的脸部周围搞得一团糟。

6.Sometimes IP aliasing is also referred to as network interface aliasing or logical interfaces.IP别名有时候也称为网络接口别名（networkinterfacealiasing）或逻辑接口（logicalinterface）。

7.IP aliasing lets you configure an agent so that it appears as though the load is coming from different IP addresses during an HTTP test run.IP混淆使您可以配置一个代理，在HTTP测试运行期间就好像负载是来自不同的IP地址。

8.Aided by a succeeding digital signal processing (DSP) at the receiver, aliasing free signal can be recovered.利用接收端的数字信号处理算法，原始数据可以从混叠的频谱中恢复出来。

9.In addition, line mode and zero-mode voltage wave cross each other at the point of fault which causes the natural frequency "aliasing" .此外，故障电压行波于非对称短路点发生线模与零模行波相互交叉透射，致使故障电压自然频率“混叠”。

10.Note that changing the quality level can be an expensive operation if the new level has different anti-aliasing setting.注意，改变质量级别，如果新的级别抗锯齿设置不同，可能是一个消耗极大的操作。