gyro

美式发音: [ˈdʒaɪroʊ] 英式发音: [ˈdʒaɪrəʊ]

n.同“gyroscope”；同“gyrocompass”

网络释义：陀螺仪(Gyroscopes)；电罗经(gyrocompass)；回转仪

复数：gyros  

网络释义

n.1.同“gyroscope”2.同“gyrocompass”3.自转旋翼飞机

n.1.Same as gyroscope2.Same as gyrocompass3.a sandwich consisting of meat cooked on a spita metal rod that turns near a fire and salad eaten on pita bread. The British word is doner kebab.4.a gyroscope1.Same as gyroscope2.Same as gyrocompass3.a sandwich consisting of meat cooked on a spita metal rod that turns near a fire and salad eaten on pita bread. The British word is doner kebab.4.a gyroscope

1.陀螺仪(Gyroscopes) 3. 旋转，回旋 gyroscopic 陀螺仪，回转仪 gyro 2. 陀螺仪，回转仪 dreidel ...

4.罗经系统ADAR)、电子海图显示与信息系统(ECDIS)、罗经系统(GYRO)、全球海上遇险与安全系统(GMDSS)、磁罗经、溢油雷达、VS…

5.陀螺仪感应器轰倾卸车(Dump)、轰轰赛车(Formula)、轰轰回旋机(Gyro)、轰轰铲土车(Dozer)、轰轰潜水艇(Marine)所组合而成。

造句带翻译释义:,回转仪

1.Compared with laser gyro, it has no both high power supply and mechanical vibrating elements.和激光陀螺相比没有高电源，也没有机械抖动部件。

2.The coarse north-seeking time of a mechanical gyro theodolite is an important factor to decide north-seeking efficiency.机械陀螺经纬仪初寻北时间的长短是决定其寻北效率的关键因素。

3.Spirit levels on the gyro may be used to determine whether the instrument has settled with a list.陀螺上的气泡水准仪可用以确定仪表的放置是否倾斜。

4.The course indication of repeaters does not match that of gyro compass.主罗经和分罗经航向示度不匹配。

5.When a position gyro is used in the pitch plane the missile is usually launched at a set elevation.当位置陀螺用在俯仰平面上的时候，导弹通常以一个设定的仰角发射。

6.Compared with mechanical gyro, it has no rotating highly components and it is insensitive to acceleration.光纤陀螺和机械陀螺相比，没有高速转动部件，对加速度不敏感；

7.Increase the throttle (collective). Just as the throttle leaves zero, gyro calibration is performed.缓慢增加油门，仅仅让油门离开最低位，陀螺仪开始工作。

8.Gyro-TWT with a spiral corrugated waveguide always has been a hot point for research by scholars from 1998.从1998年至今螺旋波纹波导回旋行波管放大器一直是各国学者研究的热点。

9.The gyro vertical utilizes a gyroscope as an integrating device to obtain the average position of a pendulous gravity reference.垂直陀螺利用一个陀螺仪作为积分装置以得摇摆不定的重力基准线的平均位置。

10.Usually in gyro designs the shaft member tends to run hotter than the outer member.在陀螺的设计中，转轴构件通常比外部构件要热一些。